Năng lượng trong tụ điện - mất?

Năng lượng được lưu trữ trong một tụ điện là

U = \frac{1}{2} C V^{2}

$U= \dfrac{1}{2} CV^2$

Vì vậy, khi tôi có một siêu tụ điện 1F tích điện đến 1V, năng lượng là 0,5 J. Khi tôi kết nối một siêu tụ điện thứ hai, song song 1F điện tích sẽ phân phối và điện áp sẽ giảm một nửa. Sau đó

U = \frac{1}{2} 2 F (0.5 V)^{2} = 0.25 J

$U = \dfrac{1}{2} 2F (0.5V)^2 = 0.25 J$

What happened to the other 0.25 J?

capacitor

— Federico Russo
nguồn

@W5VO: How's that? I don't see anything about losses in the equations.

— Federico Russo

W5Vo: You are forgetting that charge must also be conserved.

— Olin Lathrop

@OlinLathrop Yes, you're right.

— W5VO

Federico, given a spherical cow on a frictionless surface :) (which is what your math is doing), why do you assume the voltage will end up at 1/2V? If the charge is constant, I'd imagine both caps would settle in at something more like 0.71V ... preserving the stored energy.

— Bryan Boettcher

@insta: just try it. You'll see that it's V/2.

— Federico Russo

Câu trả lời:

You moved energy from one place to another and you can't do that unpunished. If you connected the two capacitors via a resistor the 0.25J went as heat in the resistor. If you just shorted the caps together much of the energy will have radiated in the spark, the rest again is lost as heat in the internal resistances of the capacitors.

further reading
Energy loss in charging a capacitor

— stevenvh
nguồn

I'll add that since the equalizing process is spontaneous, it must happen at the expense of energy. As in the water analogy, if you split the water between two containers placed at the same height, the average height of it will be lower, which means less potential energy (mgh).

— clabacchio

@clabacchio - your "less potential energy" doesn't show the energy loss, just like the energy loss isn't obvious from the lower voltage without the formula.

— stevenvh

I know, it wasn't meant to be a rigorous demonstration, just to show that the less energy is justified by the fact that "entropy", or disorder, is increased and that decreases the energy.

— clabacchio

"you can't do that unpunished". Why not? Laws of thermodynamics?

— Federico Russo

@Federico - Yes, the first. You have to perform work (energy) to move energy in or out a closed system (the capacitor).

— stevenvh

I agree with Steven, but here is another way to think about this problem.

Suppose we had two nice and perfect 1 F capacitor. These have no internal resistance, no leakage, etc. If one cap is charged to 1 V and the other at 0 V, then it's hard to see what really happens if they were connected because the current would go infinite.

Instead, let's connect them with a inductor. Let this be another ideal perfect part with no resistance. Now everything behaves nicely and can be calculated. Initially, the 1 V difference starts current flowing in the inductor. This current will increase until the two caps reach the same voltage, which is 1/2 V. Now you've got 1/8 J in one cap and 1/8 J in the other cap for a total of 1/4 J as you said. However, now we can see where the extra energy went. The inductor current is maximum at this point, and the remaining 1/4 J is stored in the inductor.

If we kept everything connected, energy would slosh back and forth between the two caps and the inductor forever. The inductor acts like a flywheel for current. When the caps reach equal voltage, the inductor current is at its maximum. The inductor current will continue, but now will decrease due to reverse voltage accross it. The current will continue until the first cap is at 0 V and the second at 1 V. At that point, all the energy has been transferred to the second cap and none is in the first cap or the inductor. Now we are at the same point we started at except that the caps are reversed. Hopefully you can see that the 1/2 J of energy will continue to slosh back and forth forever with the cap voltages and the inductor current being sine waves. At any one point, the energies of the two caps and the inductor add to the 1/2 J we started with. Energy is not lost, just constantly moved around.

Added:

This is to more directly answer your original question. Suppose you connected the two caps with a resistor in between. The voltage on both caps will be a exponential decay towards the 1/2 V steady state as before. However, there was current thru the resistor which heated it. Obviously you can't use some of the original energy to heat the resistor and end up with the same amount.

To explain this in terms of Russell's water tank analogy, instead of opening a valve between the two tanks you could put a small turbine in line. You can extract energy from that turbine as it is driven by the water flowing between the two tanks. Obviously that means the end state of the two tanks can't contain as much energy as the initial state since some was extracted as work via the turbine.

— Olin Lathrop
nguồn

And, considering that any closed loop is in fact an inductor, this even happens when you directly connect two idealized capacitors.

— leftaroundabout

Another thing to note is that while one can't directly calculate the power loss in the case of zero resistance and zero inductance, one may observe that for any non-zero amount of resistance, the amount of energy lost will asymptotically approach half of the original amount. When the inductance is zero, the time required to lose any particular fraction of that energy will be inversely proportional to the resistance. Thus, an infinitesimal resistance will dissipate half the energy in the cap in an infinitesimal amount of time.

— supercat

The transfer is lossy - whether by $I^2R$ drop in the connecting circuit or electromagnetic energy radiation or spark or other coupling. That this is so is shown a priori by the fact that you know what the end result must be ( $V/2$ each) and that this must result in an energy decrease using any "normal" connecting method. If you use near perfect wire you get near infinite currents. Every time you have the wire resistance you get double the current and losses increase linearly with decreasing resistance (decrease with $R$ , increase with $I^2$ ).

You can get a different result using an "abnormal" method.
If you use an ideal buck converter it will take Vin x Iin at the input and convert it to the "correct" Vout x Iout at the output to allow no resistive or other losses. The result is easily determined but non intuitive. Making the buck converter non-ideal can give you a result in the 95% - 99% of theoretical range.

As we have 0.5 Joule in a 2 Farad capacitor at the end of the process we know that

U = 0.5 C V^{2}

$U = 0.5 C V^2$

0.5 = 0.5 \times 2 \times V^{2}

$0.5 = 0.5 \times 2 \times V^2$

V = \sqrt{0.5} - 0.7071 V

$V = \sqrt{0.5} - 0.7071 V$

We can try that again using just one of the capacitors. As we have 0.5 J initially we get 0.25 J in one cap at the end.

0.25 = 0.5 \times 1 \times V^{2}

$0.25 = 0.5 \times 1 \times V^2$

V = \sqrt{0.5} = 0.7071 V

$V = \sqrt{0.5} = 0.7071 V$

Same result, as expected.

At first glance I thought the water tank analogy was wrong in this case, but it also works quite well for part of the problem. The difference is that, while we can model the lossy case well enough, the loss free case does not make sense physically.
ie A 10,000 litre tank 4 metres tall has energy of 0.5mgh.
h is average height = 2 metres.
Lets's have g=10 (MASCON nearby :-) ).
1 litre weighs 1 kg.

E = 0.5 m g h = 0.5 \times 10000 \times 10 \times 2 = 100 k J

$E = 0.5mgh = 0.5 \times 10000 \times 10 \times 2 = 100 kJ$

Now siphon half the water into a second identical tank.
New depth = 2m. New average depth = 1 m. New content = 5000 litre
Per tank energy = 0.5mgh = 0.5 x 5000 x 10 x 1 = 25,000 Joule
Energy in 2 tanks = 2 x 25 000 J = 50 kJ.
Half of our energy has gone missing.

With a "water buck converter" each tank would be 70.71% full and we'd have made more water.
On this aspect the model fails.
Unfortunately :-).

— Russell McMahon
nguồn