Hệ thống Debian 9 của tôi thức dậy sau 2 - 5 giây sau khi hệ thống chuyển sang chế độ ngủ (tạm dừng RAM) theo cách thủ công hoặc tự động. Vấn đề luôn xảy ra cho dù chế độ ngủ được gọi như thế nào: bằng cách đóng nắp, bằng nút nguồn hoặc từ thiết bị đầu cuối. Điều gì có thể là vấn đề?
Đây là thông tin hệ thống:
$ sudo dmidecode | grep -A3 '^System Information'
System Information
Manufacturer: LENOVO
Product Name: 20ET004LGE
Version: ThinkPad E460
$ uname -a
Linux 4.9.0-3-amd64 #1 SMP Debian 4.9.30-2+deb9u5 (2017-09-19) x86_64 GNU/Linux
Để kiểm tra thiết bị nào có thể gây ra sự cố, tôi đã kiểm tra /proc/acpi/wakeup
và sau đó vô hiệu hóa mọi thiết bị tạm thời bằng cách phát hành echo DeviceName > /proc/acpi/wakeup
, nhưng vấn đề vẫn còn tồn tại. Đây là trước khi tôi thay đổi:
$ cat /proc/acpi/wakeup
Device S-state Status Sysfs node
LID S4 *enabled platform:PNP0C0D:00
SLPB S3 *enabled platform:PNP0C0E:00
IGBE S4 *enabled pci:0000:00:1f.6
PXSX S4 *disabled
PXSX S4 *disabled pci:0000:01:00.0
PXSX S4 *disabled pci:0000:02:00.0
*disabled platform:rtsx_pci_sdmmc.0
*disabled platform:rtsx_pci_ms.0
XHCI S3 *enabled pci:0000:00:14.0
$ lspci
00:00.0 Host bridge: Intel Corporation Skylake Host Bridge/DRAM Registers (rev 08)
00:02.0 VGA compatible controller: Intel Corporation HD Graphics 520 (rev 07)
00:14.0 USB controller: Intel Corporation Sunrise Point-LP USB 3.0 xHCI Controller (rev 21)
00:14.2 Signal processing controller: Intel Corporation Sunrise Point-LP Thermal subsystem (rev 21)
00:16.0 Communication controller: Intel Corporation Sunrise Point-LP CSME HECI #1 (rev 21)
00:17.0 SATA controller: Intel Corporation Sunrise Point-LP SATA Controller [AHCI mode] (rev 21)
00:1c.0 PCI bridge: Intel Corporation Device 9d12 (rev f1)
00:1c.5 PCI bridge: Intel Corporation Sunrise Point-LP PCI Express Root Port #6 (rev f1)
00:1f.0 ISA bridge: Intel Corporation Sunrise Point-LP LPC Controller (rev 21)
00:1f.2 Memory controller: Intel Corporation Sunrise Point-LP PMC (rev 21)
00:1f.3 Audio device: Intel Corporation Sunrise Point-LP HD Audio (rev 21)
00:1f.4 SMBus: Intel Corporation Sunrise Point-LP SMBus (rev 21)
00:1f.6 Ethernet controller: Intel Corporation Ethernet Connection I219-V (rev 21)
01:00.0 Network controller: Intel Corporation Intel Dual Band Wireless-AC 3165 Plus Bluetooth (rev 99)
02:00.0 Unassigned class [ff00]: Realtek Semiconductor Co., Ltd. RTS522A PCI Express Card Reader (rev 01)
Và cuối cùng ở đây là phần có liên quan từ dmesg, sau khi tôi đặt máy vào chế độ ngủ và nó thức dậy (không có bất kỳ sửa đổi nào /proc/acpi/wakeup
):
$ sudo dmesg
[ 2591.034943] wlp1s0: deauthenticating from a4:2b:b0:ab:e2:99 by local choice (Reason: 3=DEAUTH_LEAVING)
[ 2591.044024] IPv6: ADDRCONF(NETDEV_UP): wlp1s0: link is not ready
[ 2593.048689] PM: Syncing filesystems ... done.
[ 2593.071217] PM: Preparing system for sleep (mem)
[ 2593.071490] (NULL device *): firmware: direct-loading firmware i915/skl_dmc_ver1_26.bin
[ 2593.071864] (NULL device *): firmware: direct-loading firmware iwlwifi-7265D-22.ucode
[ 2593.071880] Freezing user space processes ... (elapsed 0.002 seconds) done.
[ 2593.074134] Freezing remaining freezable tasks ... (elapsed 0.001 seconds) done.
[ 2593.075457] PM: Suspending system (mem)
[ 2593.075519] Suspending console(s) (use no_console_suspend to debug)
[ 2593.075955] sd 0:0:0:0: [sda] Synchronizing SCSI cache
[ 2593.077328] sd 0:0:0:0: [sda] Stopping disk
[ 2593.264951] ACPI : EC: event blocked
[ 2593.313967] PM: suspend of devices complete after 238.174 msecs
[ 2593.336883] PM: late suspend of devices complete after 22.910 msecs
[ 2593.337306] ACPI : EC: interrupt blocked
[ 2593.338237] xhci_hcd 0000:00:14.0: System wakeup enabled by ACPI
[ 2593.378029] PM: noirq suspend of devices complete after 41.142 msecs
[ 2593.378652] ACPI: Preparing to enter system sleep state S3
[ 2593.399563] ACPI : EC: EC stopped
[ 2593.399564] PM: Saving platform NVS memory
[ 2593.399570] Disabling non-boot CPUs ...
[ 2593.400953] smpboot: CPU 1 is now offline
[ 2593.403402] smpboot: CPU 2 is now offline
[ 2593.405121] smpboot: CPU 3 is now offline
[ 2593.408016] ACPI: Low-level resume complete
[ 2593.408131] ACPI : EC: EC started
[ 2593.408131] PM: Restoring platform NVS memory
[ 2593.408865] Suspended for 3.452 seconds
[ 2593.410052] Enabling non-boot CPUs ...
[ 2593.410111] x86: Booting SMP configuration:
[ 2593.410111] smpboot: Booting Node 0 Processor 1 APIC 0x2
[ 2593.413738] cache: parent cpu1 should not be sleeping
[ 2593.418428] CPU1 is up
[ 2593.418467] smpboot: Booting Node 0 Processor 2 APIC 0x1
[ 2593.421003] cache: parent cpu2 should not be sleeping
[ 2593.425788] CPU2 is up
[ 2593.425826] smpboot: Booting Node 0 Processor 3 APIC 0x3
[ 2593.428373] cache: parent cpu3 should not be sleeping
[ 2593.433092] CPU3 is up
[ 2593.436236] ACPI: Waking up from system sleep state S3
[ 2593.480811] ACPI : EC: interrupt unblocked
[ 2593.536245] xhci_hcd 0000:00:14.0: System wakeup disabled by ACPI
[ 2593.536310] PM: noirq resume of devices complete after 55.607 msecs
[ 2593.541114] PM: early resume of devices complete after 4.771 msecs
[ 2593.541223] ACPI : EC: event unblocked
[ 2593.541548] iwlwifi 0000:01:00.0: RF_KILL bit toggled to enable radio.
[ 2593.542111] sd 0:0:0:0: [sda] Starting disk
[ 2593.542645] rtc_cmos 00:02: System wakeup disabled by ACPI
[ 2593.548069] [drm] GuC firmware load skipped
[ 2593.768567] usb 1-7: reset high-speed USB device number 2 using xhci_hcd
[ 2593.856890] ata1: SATA link up 6.0 Gbps (SStatus 133 SControl 300)
[ 2593.857497] ata1.00: ACPI cmd ef/02:00:00:00:00:a0 (SET FEATURES) succeeded
[ 2593.857500] ata1.00: ACPI cmd f5/00:00:00:00:00:a0 (SECURITY FREEZE LOCK) filtered out
[ 2593.857545] ata1.00: ACPI cmd ef/10:09:00:00:00:a0 (SET FEATURES) succeeded
[ 2593.857767] ata1.00: supports DRM functions and may not be fully accessible
[ 2593.859546] ata1.00: ACPI cmd ef/02:00:00:00:00:a0 (SET FEATURES) succeeded
[ 2593.859548] ata1.00: ACPI cmd f5/00:00:00:00:00:a0 (SECURITY FREEZE LOCK) filtered out
[ 2593.859591] ata1.00: ACPI cmd ef/10:09:00:00:00:a0 (SET FEATURES) succeeded
[ 2593.859806] ata1.00: supports DRM functions and may not be fully accessible
[ 2593.860711] ata1.00: configured for UDMA/133
[ 2594.130430] PM: resume of devices complete after 589.312 msecs
[ 2594.130711] PM: Finishing wakeup.
[ 2594.130712] Restarting tasks ...
[ 2594.132323] [drm] RC6 on
[ 2594.133646] done.
[ 2594.754297] e1000e: enp0s31f6 NIC Link is Down
[ 2594.756068] IPv6: ADDRCONF(NETDEV_UP): enp0s31f6: link is not ready
[ 2594.969138] IPv6: ADDRCONF(NETDEV_UP): enp0s31f6: link is not ready
[ 2594.972566] IPv6: ADDRCONF(NETDEV_UP): wlp1s0: link is not ready
[ 2594.974923] iwlwifi 0000:01:00.0: L1 Enabled - LTR Enabled
[ 2594.975229] iwlwifi 0000:01:00.0: L1 Enabled - LTR Enabled
[ 2595.043353] iwlwifi 0000:01:00.0: L1 Enabled - LTR Enabled
[ 2595.043657] iwlwifi 0000:01:00.0: L1 Enabled - LTR Enabled
[ 2595.064475] IPv6: ADDRCONF(NETDEV_UP): wlp1s0: link is not ready
[ 2595.074769] iwlwifi 0000:01:00.0: L1 Enabled - LTR Enabled
[ 2595.075066] iwlwifi 0000:01:00.0: L1 Enabled - LTR Enabled
[ 2595.140447] iwlwifi 0000:01:00.0: L1 Enabled - LTR Enabled
[ 2595.140753] iwlwifi 0000:01:00.0: L1 Enabled - LTR Enabled
[ 2595.156361] IPv6: ADDRCONF(NETDEV_UP): wlp1s0: link is not ready
[ 2595.237719] IPv6: ADDRCONF(NETDEV_UP): wlp1s0: link is not ready
[ 2598.905323] IPv6: ADDRCONF(NETDEV_UP): wlp1s0: link is not ready
[ 2598.986638] wlp1s0: authenticate with a4:2b:b0:ab:e2:99
[ 2598.990338] wlp1s0: send auth to a4:2b:b0:ab:e2:99 (try 1/3)
[ 2598.992121] wlp1s0: authenticated
[ 2598.996133] wlp1s0: associate with a4:2b:b0:ab:e2:99 (try 1/3)
[ 2598.999926] wlp1s0: RX AssocResp from a4:2b:b0:ab:e2:99 (capab=0x431 status=0 aid=1)
[ 2599.003864] wlp1s0: associated
[ 2599.003986] IPv6: ADDRCONF(NETDEV_CHANGE): wlp1s0: link becomes ready
break
tham số kernel và khi bạn bị rơi tại (initramfs)
dấu nhắc, hãy làm echo mem >/sys/power/state
để tạm dừng máy của bạn. Nếu điều đó hoạt động đúng, hãy thử tìm điểm phá vỡ nó: ví dụ như acpid
tương tác với systemd-logind
(boot with systemd.unit=rescue.target
), với trình quản lý hiển thị (boot with systemd.unit=multi-user.target
) hoặc với trình quản lý nguồn máy tính để bàn của bạn (đóng môi trường máy tính để bàn của bạn).